LINE & POWER BLOCK SE
Battery powered, Dual-Chassis & Dual-Mono Preamplifier
Taking rest, while the preamplifier is overtaking control of every detail needed, is the only thing you have to do.
The Line-Block is adding the desired level and settings to the signal while the electricity needed is conveyed by the Power-Block that runs on batteries and allow you to enjoy the ultimate sound quality for at least 15 hours. After that the recharge mode is set automatically and the Power-Block works as an energy reservoir.
So you can stay hungry for the sound while your power amplifiers are being fed. Moreover, the Line-Block also guards the temperature of the Mono-Blocks through the communication channel.* And you? You can still continue on listening to your favorite records on and on.

Battery supply for audio circuits, each channel is powered by its own battery bank

Both channels, supply units and non-audio circuits are physically separated, shielded and electrically isolated

From Input to Output: Short audio signals paths without any internal wiring
FEATURES
- Battery powered, Dual-Chassis & Dual-Mono configuration
- Both channels, supply units and non-audio circuits are physically separated, shielded and electrically isolated
- Battery supply for audio circuits – each channel is powered by its own battery bank
- At least 15 hours battery operation and a smart automatic function will activate charging mode when the battery becomes empty, or preamp is switched off
- Short audio signals paths without any internal wiring
- An overall symmetrical design
- Fully differential/balanced topology
- Separate grounds for left and right channel
- Class-A operation, all discrete audio circuitry
- DC signal coupling with Servo-Control
- Symmetrical relay volume attenuator
- 2 × 120 000 µF of power supply-filter capacitance
- Adjustable input sensitivity and channel balance
- Full HT bypass function for all inputs
- The output phase invert function
- Two custom made low-noise and low-radiation toroidal transformers in decoupled and suspended mount cases
- Own physically separated and electrically isolated power supply for non-audio circuits
- Adjustable feet with integrated spikes
- User-selectable Battery or AC Mains operation mode
- Built-in Class-A headphone amplifier
- User-selectable Auto Power Off mode
- Auto brightness controlled graphical display and status LED
- Infrared remote control
- Built-in MC/MM Phono stage with remotely controlled settings
- System rem. control for power amplifier*
*works only together with appropriate BLOCK AUDIO Power Amplifier
SPECIFICATIONS
Distortion: | THD+N <0.0005 %, IMD <0.0007 % (at 6 Vrms out) |
Frequency Response: | DC – 300 kHz -0.5 dB, DC – 20 kHz -0.01 dB |
Signal/Noise Ratio: | >130 dB A weighted, >128 dB unweighted (related to full output) |
Channel Separation: | Infinite (>130 dB) |
Max. Voltage Gain: | +12 dB balanced, +18 dB unbalanced |
Input Impedance: | 40 kΩ balanced, 20 kΩ unbalanced |
Output Impedance: | 50 Ω balanced, 25 Ω unbalanced |
Maximum Output Voltage: | 20 Vrms balanced, 10 Vrms unbalanced |
Inputs: | 4 balanced (XLR) pairs, 5 unbalanced (RCA) pairs |
Phono Input: | 1 unbalanced (RCA) pair |
Outputs: | 2 balanced (XLR) pairs, 2 unbalanced (RCA) pairs |
Phones Output: | 3 pole XLR receptacle and 6.35 mm / 1⁄4″ stereo jack |
Battery Operation Time: | >15 hours |
System Remote Control: | Yes*, Neutrik RJ45 |
Power Consumption: | 150 W max. at charging, 50 W at idle, <0.5 W in Standby |
Mains Voltage: | 230 / 115 V AC ±10 %, 50 / 60 Hz (factory pre-configured) |
Dimensions – Line: | 460/18.1(w) × 105/4.1(h) × 360/14.2(d) mm/inch |
Dimensions – Power: | 460/18.1(w) × 105/4.1(h) × 360/14.2(d) mm/inch |
Weight in total: | 28 kg / 62 lbs., ~40 kg / 88 lbs. shipping |
SE FEATURES
- Special paint finish
- Upgraded Input stage transistors
- All metal Furutech RCA sockets for Phono input
COLORS

Silver

Red